NOTE: My original article contained embedded calculation errors that significantly distorted the end results. These problems have since been corrected. I apologize to anyone who was accidentally misled by this information, and sincerely thank those diligent readers who brought the issues to my attention.
Some issues seem so obvious they’re hardly worth considering. Everyone knows that Solid State Drives (SSD) are more energy-efficient than spinning disk. They don’t employ rotating platters, electro-mechanical motors and mechanical head movement for data storage, so they must consume less power – right? However, everyone also knows the cost of SSD is so outrageous that they can only be deployed for super-critical high performance applications. But does the reputation of having exorbitant prices still apply?
While these considerations may seem intuitive, they are not entirely accurate. Comparing the Total Cost of Ownership (TCO) for traditional electro-mechanical disks vs. Solid State Disks provides a clearer picture of the comparative costs of each technology.
- For accuracy, this analysis compares the purchase price (CAPEX) and power consumption (OPEX) of only the disk drives, and does not include the expense of entire storage arrays, rack space, cooling equipment, etc.
- It uses the drive’s current “street price” for comparison. Individual vendor pricing may be significantly different, but the ratio between disk and SSD cost should remain fairly constant.
- The dollar amounts shown on the graph represent a 5-year operational lifecycle, which is fairly typical for production storage equipment.
- Energy consumption for cooling has also been included in the cost estimate, since it requires roughly the amount of energy as the drives consume to maintain them in an operational state.
- 100 TB of storage capacity was arbitrarily selected to illustrate the effect of cost on a typical mid-sized SAN storage array.
The following graph illustrates the combined purchase price, plus energy consumption costs for several popular electro-mechanical and Solid State Devices.
From the above comparison, several conclusions can be drawn:
SSDs are Still Expensive – Solid State Drives remain an expensive alternative storage medium, but the price differential between SSD and electro-mechanical drives is coming down. As of this writing there is only an x5 price difference between the 800GB SSD and the 600GB, 15K RPM drive. While this is still a significant gap, it is far less that the staggering x10 to x20 price differential seen 3-4 years ago.
SSDs are very “Green” – A comparison of the Watts consumed during a drive’s “typical operation” indicate that SSD consumes about 25% less energy than 10K RPM, 2.5-inch drives, and about 75% less power than 15K RPM, 3.5-inch disks. Given that a) each Watt used by the disk requires roughly 1 Watt of power for cooling to remove the heat that is produced, and b) the cost per Kwh continues to rise every year, this significant difference become a factor over a storage array-s 5-year lifecycle.
Extreme IOPS is a Bonus – Although more expensive, SSDs are capable of delivering from 10- to 20-times more I/O’s-per-second, potentially providing a dramatic increase in storage performance.
Electro-Mechanical Disks Cost Differential – There is a surprisingly small cost differential between 3.5 inch, 15K RPM drives and 2.5 inch 10K RPM drives. This may justify eliminating 10K disks altogether and deploying a less complex 2-tiered array using only 15K RPM disks and 7.2K disks.
Legacy 3.5 Inch Disks – Low capacity legacy storage devices (<146GB) in a 3-5-inch drive form-factor consume too much energy to be practical in a modern, energy-efficient data center (this includes server internal disks). Any legacy disk drive smaller than 300 GB should be retired.
SATA/NL-SAS Disks are Inexpensive – This simply re-affirms what’s already known about SATA/NL-SAS disks. They are specifically designed to be inexpensive, modest performance devices capable of storing vast amounts of low-demand content on-line.
The incursion of Solid State Disks into the industry’s storage mainstream will have interesting ramifications not only for the current SAN/NAS arrays, but also may impact a diverse set of technologies that have been designed to tolerate the limitations of an electro-mechanical storage world. As they say, “It’s a brave new world”.
Widespread deployment of SSD will have a dramatic impact on the storage technology itself. If SSDs can be implemented in a cost-effective fashion, why would anyone need an expensive and complex automated tiering system to decrement data across multiple layers of disk? Because of its speed, will our current efforts to reduce RAID rebuild times still be necessary? If I/O bottlenecks are eliminated at the disk drive, what impact will it have on array controllers, data fabric, and HBAs/NICs residing upstream of the arrays?
While it is disappointing to find SSD technology still commands a healthy premium over electro-mechanical drives, don’t expect that to remain the case forever. As the technology matures prices will decline when user acceptance grows and production volumes increase. Don’t be surprised to see SSD technology eventually eliminate the mechanical disk’s 40-year dominance over the computer industry.
For those of you interested in examining the comparison calculations, I’ve included the following spreadsheet excerpts contain detailed information used to create the graph.
If you believed all the media hype and vendor pontifcations three years ago, you would have thought for sure that Fibre Channel was teetering on the edge of oblivion. According to industry hype, 10Gbps Ethernet and the FCoE protocol were certain to be the demise of Fibre Channel. One Analyst even went so far as to state, “IP based storage networking technologies represent the future of storage”. Well as they say, “Don’t believe everything you read”.
In spite of a media blitz designed to convince everyone that Fibre Channel was going extinct, industry shipments and FC implementation by IT storage professionals continued to blossom. As 16Gbps Fibre Channel rapidly grew in acceptance, the excitement around 10GbE diminished. In a Dell’Oro Group report for 4Q12, fibre channel Director, switch, and adapter revenues surpassed $650 million, while FCoE champion Cisco suffered through soft quarterly results.
So what makes Fibre Channel network technology so resilient?
• Simplicity – FCP was designed with a singular purpose in mind, and does not have to contend with a complex protocol stack.
• Performance – a native 16Gbps FC port is 40% faster than a 10GbE network, and it too can be trunked to provide aggregate ISL bandwidth up to 128 Gbps.
• Low Latency – FC fabric is not penalized by the additional 2-hop latency imposed by routing data packets through a NAS server before it’s written to disk.
• Parity of Cost – The dramatic reduction in expense promised by FCoE has failed to materialize. The complexity and cost of pushing data at NN_Ghz is fairly consistent, regardless of what protocol it used.
• Efficiency – Having a Fibre Channel back-end network supports such capabilities as LAN-less backup technology, high speed data migration, block-level storage virtualization, and in-fabric encryption.
An excellent indicator that Fibre Channel is not falling from favor is Cisco’s recent announcement of their new 16Gbps MDS 9710 Multilayer Director and MultiService Fabric Switch. Cisco was a major proponent of 10GbE and the FCoE protocol, and failed to update their aging MDS 9500 family of Fibre Channel Directors and FC switches. (http://searchstorage.techtarget.com/news/2240182444/Cisco-FC-director-and-switch-moves-to-16-Gbps-new-chassis) This left Brocade with a lion’s share of a rapidly growing 16 Gbps Fibre Channel market. For Brocade, it produced a record quarter for FC switch revenues, while Cisco struggled with sagging sales.
Another influencing factor in FC longevity of is the average IT department’s need for extremely high-bandwidth storage network capabilities. Prior to 10GbE technology, Ethernet LANs performed quite well at 1GbE (or some trunked variation of 1GbE). The majority of the fibre channel world still depends upon 4Gbps FC, with 8Gbps technology recently starting to make significant inroads in the data center. Given the fairly leisurely pace of migration to higher performance for the SAN and NAS fabric technology. Except for a fairly small percent of IT departments that actually require high performance / high throughput, the lure of a faster interface alone has a limited amount of allure.
So which network technology will win? Who knows (or even cares)? There are usually bigger issues to overcome than what the back-end “plumbing” is made of. It’s far more important to implement the most appropriate technology for the task at hand. That could be Ethernet, Fibre Channel, Infiniband, or some other future network scheme. The key is to select your approach based on functionality and efficiency, not what is being hyped as “the next great thing” in the industry. In spite of all the hyperbole, Fibre Channel isn’t going away any time soon.
As Samuel Clemens (aka Mark Twain) said after hearing that his obituary had been published in the New York Journal, “The reports of my death are greatly exaggerated”.
Like most other things, technology suffers from advancing age. That leading-edge wonder of just a few years ago is today’s mainstream system. This aging process creates great headaches for IT departments, who constantly see “the bar” being moved upward. Just when it seems like the computing environment is under control, equipment needs to be updated.
Unless a company is well disciplined in enforcing their technical refresh cycle, the aging process can also lure some organizations into a trap. The thinking goes something like this – “Why not put off a technology update by a year or two? Budgets are tight, the IT staff is overworked, and things seem to be going along just fine.” It makes sense, doesn’t it?
Well, not exactly. If you look beyond the purchase and migration expenses, there are other major cost factors to consider.
Power Reduction: There have been major changes in storage device energy efficiency over the past decade. Five years ago the 300GB, 15K RPM 3.5-inch drive was leading-edge technology. Today, that has disk been superseded by 2.5-inch disks of the same speed and capacity. Other than its physical size, other major changes are the disk’s interface (33% faster than Fibre Channel) and its power consumption (about 70% less than a 3.5-inch drive). For 100TB of raw storage, $3577 per year could be saved by reduced power consumption alone.
Cooling Cost Reduction: A by-product of converting energy to power is heat, and systems used to eliminate heat consume power too. The following chart compares the cost for cooling 100TB of 3.5-inch disks with the same capacity provided by 2.5-disks. Using 2.5-inch disks, cooling costs could be reduced by $3548 per year, per 100TB of storage.
Floor Space Reduction: Another significant data center cost is for floor space. This expense can vary widely, depending on the type resources provided and level of high availability guaranteed by the Service Level Agreement. For the purpose of cost comparison, we’ll take a fairly conservative $9600 per equipment rack per year. We will also assume fractional amounts are available, although in the real world full rack pricing might be required. Given the higher density provided by 2.5-inch disks, a cost savings of $9,371 would be achieved.
In the example above, simply replacing aging 300GB, 15K RPM 3.5-inch FC disk drives with the latest 300GB, 15K RPM 2.5-inch FC disk drives will yield the following operational costs (OPEX) savings:
Reduced power $ 3,577
Reduced cooling $ 3,548
Less floor space $ 9,371
Total Savings $ 16,496 per 100TB of storage
Over a storage array’s standard 5-year service cycle, OPEX savings could result in as much as $82K dollars or more.
Addition benefits from a storage refresh might also include tiering storage (typically yielding around a 30% savings over non-tiered storage), reduced support contract costs, and less time spent managing older, more labor-intensive storage subsystems. There is also an opportunity for capital expense (CAPEX) savings by cleverly designing cost-optimized equipment, but that’s a story for a future article.
Don’t be misled into thinking that a delay of your storage technical refresh cycle will save money. In the end it could be a very costly decision.
For the past several years the business community and IT industry has been buzzing about “Big Data”. The Holy Grail of business is to become a “data driven Enterprise” by efficiently mining vast amounts of internal and external data. Identifying unforeseen relationships is considered to be an excellent method to drive sales growth and extend a company’s market share. While there may be value in this approach, “Big Data” analysis will only be as successful as the value of the stored content it examines.
Since the beginning of the computer industry, organizations have collected and stored amounts of information well beyond what the law requires. Management in general holds the belief that legacy data may contain vast treasure troves of unidentified residual value. In some cases it has been justified, since an ability to recall and examine historical content has proven to identify valuable relationships. However, in some situations it is questionable just how significant the recently discovered patterns and associations may be.
Recently a new wave of analytical tools and data structures has emerged to capitalize on the growing pool of stored data. They provide new capabilities to combine and analyze dissimilar information, produce associations between obscure facts, and allow vast quantities of data to be inspected for unexpected relationships. The application of these tools provides new methods for analyzing customer needs, trends, and buying patterns.
While some of retained data may yield valuable insight into an organization’s market, expecting everything in the archive to hold such nuggets can be unrealistic, problematic, and prohibitively expensive to maintain.
Changing Customer Priorities – Today’s markets are highly dynamic, with major change occurring randomly on frequent basis. Much of the captured information has a finite shelf life. Over time customers experience life changing events, families mature and disburse, personal finances may improve or decline, and individual priorities shift. Critical buying patterns of a decade ago may have little relevance in today’s market.
The Impact of External Events – Recent political, economic, and natural phenomena have re-shaped our society. Dramatic changes in our travel patterns occurred after 9/11. Hurricane Katrina, along with the Indonesia and Japanese tsunamis effected our thinking about preparations for natural disasters. Senseless killings at a theater in Aurora CO, a shopping mall in Tucson AZ, and a Sikh Temple in Milwaukee WI make us reconsider our attendance at social events and modify entertainment plans. The impact of a protracted global recession negatively impacts spending trends, financial investments, retirement plans, and even our expectations for our future. Key indicators of a decade ago may provide marginal value today.
Attrition of Value – Another issue with analyzing vast quantities of stored legacy data is the problem of long-term retention of content with questionable business value. All data is not created equal! Details about receivables may hold a level of value for many years, while a file about last week’s cafeteria specials is almost worthless by the following week. A good example this is a management PowerPoint sent to all employees. The original copy may retain its importance for an extended period of time, but dozens of identical copies kept in user accounts provide little incremental value.
Content Duplication –In any given SAN it is typical to find several outdated copies of the same data, abandon “clone” files once needed for testing, data with expired business value, unnecessary copies of temp files, orphaned directories from departed users, and residue left from ancient applications and databases. Unless a continuous process is in place to preen and update active storage, licensing costs for “Big Data” analytical tools and systems may be prohibitive. Even if the IT budget can absorb the cost, performance will suffer from having to load, filter, and index huge quantities of irrelevant data.
While valuable insight may be gained from customer content buried deep within an organization’s data repository, due diligence should be performed on existing content to verify its value and uniqueness. The old saying “garbage in-garbage out” is just as valid in today’s “Big Data” world as it was in the heyday of the mainframe.
It’s hard to retire a perfectly good storage array. Budgets are tight, there’s a backlog of new projects in the queue, people are on vacation, and migration planning can be difficult. As long as there is not a compelling reason to take it out of service, it’is far easier to simply leave it alone and focus on more pressing issues.
While this may be the path of least resistance, it can come at a high price. There are a number of good reasons why upgrading storage arrays to modern technology may yield superior results and possibly save money too!
Capacity – When your aging disk array was installed several years ago, 300 GB, 10K RPM, FC disk drives were mainstream technology. It was amazing to realize you could squeeze up to 45 TB in a single 42U equipment rack! Times have changed. The same 10K RPM DISK drive has tripled in capacity, providing 900 GB in the same 3.5 inch disk drive “footprint”. It’s now possible to get 135 TB (a 300% capacity increase) into the same equipment rack configuration. Since data center rack space currently costs around $3000 per month, that upgrade alone will dramatically increase capacity without incurring any increase in floor-space cost.
Density – Previous generation arrays packaged from (12) to (15) 3.5 inch FC or SATA disk drives into a single rack-mountable 4U array. Modern disk arrays support from (16) 3.5 inch disks per 3U tray, to (25) 2.5 inch disks in a 2U tray. Special ultra-high density configurations may house up to (60) FC, SAS, or SATA DISK drives in a 4U enclosure. As above, increasing storage density within an equipment rack significantly increases capacity while requiring no additional data center floor-space.
Energy Efficiency – Since the EPA’s IT energy efficiency study in 2007 (Report to Congress on Server and Data Center Energy Efficiency, Public Law 109-431), IT manufacturers have increased efforts to improve the energy efficiency of their products. This has resulted in disk drives that consume from 25% to 33% less energy, and storage array controllers lowering power consumption by up to 30%. That has had a significant impact on energy costs, including not only the power to run the equipment, but also power to operate the cooling systems needed to purge residual heat from the environment.
Controller Performance – Storage array controllers are little more than specialized servers designed specifically to manage such functions as I/O ports, disk mapping, RAID and cache operations, and execution of array-centric internal applications (such as thin provisioning and snapshots). Like any other server, storage controllers have benefited from advances in technology over the past few years. The current generation of disk arrays contain storage controllers with from 3 to 5 times the processing power of their predecessors.
Driver Compatibility – As newer technologies emerge, they tend to focus on developing software compatibility with the most recently released products and systems on the market. With the passage of time, it becomes less likely for storage arrays to be supported by the latest and greatest technology on the market. This may not impact daily operations, but it creates challenges when a need arises to integrate aging arrays with state-of-the-art systems.
Reliability – Common wisdom used to be that disk failure characteristics could be accurately represented by a ”bathtub graph”. The theory was the potential for failure was high when a disk was new. It then flattened out at a low probability throughout the disk’s useful life, then took a sharp turn upswing as it approached end-of-life. This model implied that extending disk service life had no detrimental effects until it approached end-of-life for the disks.
However over the past decade, detailed studies by Google and other large organizations with massive disk farms have proven the “bathtub graph” model incorrect. Actual failure rates in the field indicate the probability of a disk failure increases by 10% – 20% for every year the disk is in service. It clearly shows the probability of failure increases in a linear fashion over the disk’s service life. Extending disk service-life greatly increases the risk for disk failure.
Service Contracts –Many popular storage arrays are covered by standard three-year warranties. This creates a dilemma, since the useful service life of most storage equipment is considered to be either four or five years. When the original warranty expires, companies must decide whether to extend the existing support contract (at a significantly higher cost), or transitioning to a time & materials basis for support (which can result in some very costly repairs).
Budgetary Impact – For equipment like disk arrays, it is far too easy to fixate on replacement costs (CAPEX), and ignore the ongoing cost of operational expenses (OPEX). This may avoid large upfront expenditures, but it slowly bleeds the IT budget to death by having to maintain increasingly inefficient, fault-prone, and power hungry equipment.
The solution is to establish a program of rolling equipment replenishment on a four- or five-year cycle. By regularly upgrading 20% to 25% of all systems each year, the IT budget is more manageable, equipment failures are controlled, and technical obsolescence remains in check.
Getting rid of familiar things can be difficult. But unlike your favorite slippers, the LazyBoy recliner, or your special coffee cup, keeping outdated storage arrays in service well beyond their prime can cost your organization plenty.
There’s a quiet revolution going on in large data centers. It’s not as visible or flashy as virtualization or deduplication, but at least equal in important.
As its name implies, SAN “fabric” is a dedicated network that allows servers, storage arrays, backup & recovery systems, replication devices, and other equipment to pass data between systems. Traditionally this has been comprised of 4Gbps Fibre Channel and 1Gbps Ethernet channels. However, a new family of 8Gbps and 16Gbps Fibre Channel, 6Gbps and 12Gbps SAS, and 10Gbps Ethernet are quietly replacing legacy fabric with links capable of 2 – 4 times the performance.
The following is a comparison of the maximum throughput rates of various SAN fabric links:
Performance ranges from the relatively outdated 1Gbps channel (Ethernet or FC) capable of supporting data transfers of up to 100 MB per second, to 16Gbps Fibre Channel capable of handling 1940 MB per second. Since all are capable of full duplex (bi-directional) operations, the sustainable throughput rate is actually twice the speed indicated in the chart. If these blazing new speeds are still insufficient, 10Gbps Ethernet, 12Gbps SAS, and 16Gbps Fibre Channel can be “trunked” – bundled together to produce an aggregate bandwidth equal to the number of individual channels tied together. (For example, eight 16Gbps FC channels can be bundled to create a 128Gbps “trunk”.)
In addition to high channel speeds, 10Gbps Ethernet and 16Gbps Fibre Channel both implement a 64b/66b encoding scheme, rather than the 8b/10b encoding scheme used by lower performance channels. The encoding process improves the quality of the data transmission, but at a cost. An 8b/10b encoding process decreases available bandwidth by 20%, while 64b/66b encoding only reduces bandwidth by 3.03%. This significantly increases data transfer efficiency.
While 8/16Gbps Fibre Channel and 10Gbps Ethernet are changing the game at the front-end, SAS is revolutionizing the back-end disk drive connections as well. For over a decade, enterprise-grade disks had 2Gbps or 4Gbps ports, and were attached to a Fiber Channel Arbitrated Loop (FC-AL). Like any technologies using loop technology, low traffic enjoyed maximum speed but performance dropped off as demand increased. Under heavy load conditions, the back-end bus could become a bottle-neck.
SAS will change that for two reasons. First it uses switched technology, so every device attached to the controller “owns” 100% of the bus bandwidth. The latency “dog leg pattern” found on busy FC-AL busses is eliminated. Secondly current SAS drives are shipping with 6Gbps ports, which are 50% faster than 4Gbps Fibre Channel. Just over the horizon are 12Gbps SAS speeds that will offer a 300% increase in bandwidth to the disks, and do it over switched (isolated) channels.
Recent improvements in fabric performance will support emerging SSD technology, and allow SANs to gracefully scale to support storage arrays staggering under a growth rate of 40% – 50% per year.
It’s easy to hold onto the concept that IT is all about systems, networks, and software. This has been accepted wisdom for the past 50-years. It’s a comfortable concept, but one that is increasing inaccurate and downright dangerous as we move into an era of “big data”! In today’s world not about systems, networks, applications, or the datacenter – it’s all about the data!
For decades accumulated data was treated as a simply bi-product of information processing activities. However, there is growing awareness that stored information is not just digital “raw material”, but a corporate asset containing vast amounts of innate value. Like any other high-value asset, it can be bought or sold, traded, stolen, enhanced, or destroyed.
A good analogy for today’s large-scale storage array is to that of a gold mine. Data is the nuggets of gold embedded in the mine. The storage arrays containing data are the “mine” that houses and protects resident data. Complex and sophisticated hardware, software, tools, and skill-sets are simply tools used to locate, manipulate, and extract the “gold” (data assets) from its surrounding environment. The presence of high value “nuggets” is the sole reason the mining operation exists. If there was no “gold”, the equipment used to extract and/or manipulate it would be of little value.
This presents a new paradigm. For years storage was considered some secondary peripheral that was considered only when new systems or applications were being deployed. Today storage has an identity of its own that is independent from the other systems and software in the environment.
Data is no longer just a commodity or some type of operational residue left over from the computing process. “Big Data” forces a shift in focus from IT assets deployment and administration to the management of high-value data assets. It dictates that data assets sit at the center of concentric rings, ensuring security, recoverability, accessibility, performance, data manipulation, and other aspects of data retention are addressed as abstract requirements with unique requirements. Now information must be captured, identified, valued, classified, assigned to resources, protected, managed according to policy, and ultimately purged from the system after its value to the organization has been expended.
This requires a fundamental change in corporate culture. As we move into an era of “big data” the entire organization must be aware of information’s value as an asset, and the shift from technology-centric approaches for IT management. Just like gold in the above analogy, users must recognize that all data is not “created equal” and delivers different levels of value to an organization for specific periods of time. For example, financial records typically have a high level of inherent value, and retain a level of value for some defined period of time. (The Sarbanes-Oxley act requires publicly-traded companies to maintain related audit documents for no less than seven years after the completion of an audit. Companies in violation of this can face fines of up to $10 million and prison sentences of 20 years for Executives.)
However, differences in value must be recognized and managed accordingly. Last week’s memo about the cafeteria’s luncheon specials must not be retained and managed in the same fashion as an employee’s personnel record. When entered into the system, information should be classified according to a well-defined set of guidelines. With that information it can be assigned to an appropriate storage tier, backed up on a regular schedule, kept available on active storage as necessary, later written to low-cost archiving media to meet regulatory and litigation compliance needs. Once data no longer delivers value to an organization, it can be expired by policy, freeing up expensive resources for re-use.
This approach moves IT emphasis away from building systems tactically by simply adding more-of-the-same, and replacing it with a focus on sophisticated management tools and utilities that automate the process. Clearly articulated processes and procedures must replace “tribal lore” and anecdotal knowledge for managing the data repositories of tomorrow.
“Big Data” ushers in an entirely new way of thinking about information as stored, high-value assets. It forces IT Departments to re-evaluate their approach for management of data resources on a massive scale. At a data growth rate of 35% to 50% per year, business-as-usual is no longer an option. As aptly noted in a Bob Dylan song, “the times they are a-changin”. We must adapt accordingly, or suffer the consequences.
With today’s technology there can be no status quo. As the IT industry advances, so must each organization’s efforts to embrace new equipment, applications, and approaches. Without an ongoing process of improvement, IT infrastructures progressively become outdated and the business group they support grows incrementally less effective.
In September of 2010, the INCITS T11.2 Committee ratified the standard for 16Gbps Fibre Channel, ushering in the next generation of SAN fabric. Unlike Ethernet, Fibre Channel is designed for one specific purpose – low overhead transmission of block data. While this capability may be less important for smaller requirements where convenience and simplicity are paramount, it is critical for larger datacenters where massive storage repositories must be managed, migrated, and protected. For this environment, 16Gbps offers more than twice the bandwidth of the current 8Gbps SAN and 40% more bandwidth than the recently released 10Gbps Ethernet with FCoE (Fibre Channel over Ethernet).
But is an investment in 16Gbps Fibre Channel justified? If a company has reached a point where SAN fabric is approaching saturation or SAN equipment is approaching retirement, then definitely yes! Here is how 16Gbps stacks up against both slower fibre channel implementations and with 10Gbps Ethernet.
|Port Speed||Protocol||Average HBA/NIC Price||Transfer
|Transfer Time for 1TB||Bandwidth
|LPE16002||16 Gbps||Fibre Channel||$1,808||1939 MB/sec.||1.43 Hrs.||$0.93||160%|
|OCe11102||10 Gbps||Ethernet||$1,522||1212 MB/sec.||2.29 Hrs.||$1.26||100%|
|LPe12002||8 Gbps||Fibre Channel||$1,223||800 MB/sec.||3.47 Hrs.||$1.53||65%|
|LPe11000||4 Gbps||Fibre Channel||$891||400 MB/sec.||6.94 Hrs.||$2.23||32%|
This table highlights several differences between 4/8/16 Gbps fibre channel and 10Gbps Ethernet with FCoE technology (sometimes marketed as Unified Storage). The street prices for a popular I/O Controller manufacturer clearly indicates there are relatively small differences between controller prices, particularly for the faster controllers. Although the 16Gbps HBA is 40% quicker, it is only 17% more expensive!
However, a far more important issue is that 16Gbps fibre channel is backward compatible with existing 4/8 Gbps SAN equipment. This allows segments of the SAN to be gradually upgraded to leading-edge technology without having to suffer the financial impact of legacy equipment rip-and-replace approaches.
In addition to providing a robust, purpose-built infrastructure for migrating large blocks of data, it also offers lower power consumption per port, a simplified cabling infrastructure, and the ability to “trunk” (combine) channel bandwidth up to 128Gbps! It doubles the number of ports and available bandwidth in the same 4U rack space for edge switches, providing the potential for a saving of over $3300 per edge switch.
Even more significant is that 16Gbps provides the additional performance necessary to support the next generation of storage, which will be based on 6Gbps and 12Gbps SAS disk drives. Unlike legacy FC storage, which was based upon 4Gbps FC-AL arbitrated loops, the new SAS arrays are on switched connections. Switching provides a point-to-point connection for each disk drive, ensuring every 6Gbps SAS connection (or in the near future, 12Gbps SAS connection) will have a direct connection to the SAN fabric. This eliminates backend saturation of legacy array FC-AL shared busses, and will place far greater demand for storage channel performance on the SAN fabric.
So do the benefits of 16Gbps fibre channel outweigh its modest price premium? Like many things in life – it depends! Block-based 16Gbps fibre channel SAN fabric is not for every storage requirement, but neither is file-based 10Gbps FCoE or iSCSI. If it is a departmental storage requirement or an environment where NAS or iSCSI has previously been deployed, then replacing the incumbent protocol with 16Gbps fibre channel may or may not have merit. However, large SAN storage array are particularly dependent on high performance equipment specifically designed for efficient data transfers. This is an arena where the capabilities and attributes of 16Gbps fibre channel will shine.
In any case, the best protection against making a poor choice is to thoroughly research the strengths and weaknesses of each technology and seek out professional guidance from a vendor-neutral storage expert with a Subject Matter Expert level understanding of the storage industry and its technology.
It is somewhat surprising just how many skilled IT specialists still shy away from eliminating traditional internal boot disks with a Boot-from-SAN process. I realize old habits die hard and there’s something reassuring about having the O/S find the default boot-block without needing human intervention. However the price organizations pay for this convenience is not justifiable. It simply adds waste, complexity, and unnecessary expense to their computing environment.
Traditionally servers have relied on internal disk for initiating their boot-up processes. At start-up, the system BIOS executes a self-test, starts primitive services like the video output and basic I/O operations, then goes to a pre-defined disk block where the MBR (Master Boot Record) is located. For most systems, the Stage 1 Boot Loader resides on the first block of the default disk drive. The BIOS loads this data into system memory, which then continues to load Stage 2 Boot instructions and ultimately start the Operating System.
Due to the importance of the boot process and the common practice of loading the operating system on the same disk, two disks drives with a RAID1 (disk mirroring) configuration is commonly used to ensure high availability.
Ok, so far so good. Then what’s the problem?
The problem is the disks themselves. Unlike virtually every subsystem in the server, these are electro/mechanical devices with the following undesirable issues:
- Power & Cooling – Unlike other solid-state components, these devices take a disproportionately large amount of power to start and operate. A mirrored pair of 300GB, 15K RPM disks will consume around .25 amps of power and need 95.6 BTUs for cooling. Each system with internal disk has its own miniature “space heater” that aggravates efforts to keep sensitive solid state components cool.
- Physical Space – Each 3.5 inch drive is 1” x 4.0” x 5.76” (or 23.04 cubic inches) in size, so a mirrored pair of disks in a server represents an obstacle of 46.08 cubic inches that requires physical space, provisions for mounting, power connections, air flow routing, and vibration dampening to reduce fatigue on itself and other internal components.
- Under-utilized Capacity – As disk drive technology continues to advance, it becomes more economical to manufacture higher capacity disk drives than maintain an inventory of lower capacity disks. Therefore servers today are commonly shipped with 300GB or 450GB boot drives. The problem is that Windows Server 2008 (or similar) only needs < 100GB of space, so 66% of the disk’s capacity is wasted.
- Backup & Recovery – Initially everyone plans to keep only the O/S, patches and updates, log files, and related utilities on the boot disk. However, the local disk is far too convenient and eventually has other files “temporarily” put on it as well. Unfortunately some companies don’t include boot disks in their backup schedule, and risk losing valuable content if both disks are corrupted. (Note: RAID1 protects data from individual disk failures but not corruption.)
Boot-from-SAN does not involve a PXE or tftp boot over the network. It is an HBA BIOS setting that allows SAN disk to be recognized very early in the boot process as a valid boot device, then points the server to that location for the Stage 1 Boot Loader code. It eliminates any need for internal disk devices and moves the process to shared storage on the SAN. It also facilitates the rapid replacement of failed servers (all data and applications remain on the SAN), and is particularly useful for blade systems (where server “real-estate” is at a premium and optimal airflow is crucial).
The most common argument used against Boot-from-SAN is “what if the SAN is not available”. On the surface it sounds like a valid point, but what is the chance of that occurring with well-designed SAN storage? Why would that be any different than if the internal boot disk array failed to start? Even if the system started internally and the O/S loaded, how much work could a server do if it could not connect to the SAN? The consequences of any system failing to come up to an operational state are the same, regardless if it uses a Boot-from-SAN process or boots up from internal disks.
For a handful servers, this may not be a very big deal. However, when you consider the impact on a datacenter running thousands of servers the problem becomes obvious. For every thousand servers, Boot-from-SAN eliminates the expense of two thousand internal disks, 240 amps of current, the need for 655,300 BTUs of cooling, greatly simplifies equipment rack airflow, eliminates 200TB of inaccessible space, and measurably improves storage manageability and data backup protection.
Boot-from-SAN capability is built into most modern HBA BIOS’s and is supported by almost every operating system and storage array on the market. Implementing this valuable tool should measurably improve the efficiency of your data center operation.
We’re struggling back from the depths of recession, but IT budgets remain tight. The business community is demanding an ever-increasing amount of functionality from the datacenter. Managing IT today is an exercise in being-between-a-rock-and-a-hard-place.
However in the midst of this seemingly impossible situation, there are bright spots. Most datacenters are a veritable treasure-trove of opportunity for efficiency improvements. Some examples include:
- Typically over 90% of all data sitting on active disk has not been accessed in over 6-months.
- An average physical server (non-virtualized) is less than 30% utilized.
- Floor-space for a 42U equipment rack costs around $3000 per month (or $36,000 per year, per rack). That equate to over $850 per U (1.75 inches), per year!
- Replacing rack servers with blade servers can reduce the amount of rack space by at least 36% (typically much more).
- According to Intel, upgrading servers to newer, more powerful systems can yield a consolidation ratio of between 4:1 and 7:1.
- Standardizing on 45U high equipment racks, rather than 42U racks will reduce your datacenter foot print by (1) rack for every (14) equipment racks installed.
- The purchase price for multi-tiered storage equipment is normally 25% – 35% less than traditional storage arrays.
- Replacing boot disks with boot-from-SAN technology may eliminate literally hundreds of underutilized disks, along with the power and cooling they require.
- 2.5 inch disk drives need 40% less energy (and cooling) than a 3.5 inch disk drive equivalent of the same capacity.
- In a properly managed environment, LTO tape media will store seldom-used data for up to 30-years with a 99.999% recovery rate – at under $.03 per GB!
- A well-designed SAN topology can lower the fibre channel port cost from $1800-per-port to around $300-per-port (an 80%+ reduction in cost)!
- Well-designed and properly delivered IT training can increase productivity by 17% – 21% per FTE.
So where to start? The quickest way is to perform a high-level assessment of the datacenter to identify the most promising opportunities. This can be done by internal personnel, but it is a task most effectively done by an outside IT consulting firm that specializes in datacenter optimization. They can devote the time necessary to promptly complete the task, and are not biased by day-to-day familiarity with the equipment that may mask issues. Additionally, an professional datacenter consultant can deliver an industry-wide perspective, suggest best practices, and offer out-of-the-box thinking that is not influenced by an organization’s current culture.
Once all areas for improvement have been exposed and documented, the data should be transitioned into the architectural development and planning cycle to ensure any changes will not adversely impact other areas of operation, and are executed on a manageable and sustainable timeline.
Unfortunately there is no “magic cure” for a difficult economy or anemic IT budgets. However, most datacenters offer more than enough opportunity to enable you to shave 20% to 30% off the operating budget.